Datasheet: Wearable Mesh Rider Radio – 5650~5755 MHz (Japan Robotics)




The Multiband Wearable RM-5700-12W3 Mesh Rider Radio operates in the 5700-MHz frequency range allowing it to be used in the Japanese Unmanned Aircraft band. Each device is a node on a long-range Mesh Rider network and uses Wi-Fi to bridge Tablets and Smartphones onto the network. The Multiband Wearable Mesh Rider Radio is used by tactical teams to collaborate by streaming voice, video, and data on a fast, low latency, and encrypted network.

The Multiband Wearable RM-5700-12W3 Mesh Rider Radio was designed to be conveniently carried and is capable of streaming HD video to a teammate up to 1 km away. External antenna ports are included to integrate with high-gain antennas for longer distances. The radio is available with or without a battery pack, or with additional interfaces for fixed installations.

As with all Mesh Rider Radio form factors, the Multiband Wearable Mesh Rider Radio is available in many frequency bands between 900 MHz and 6 GHz freq range. This flexibility allows customers to use their industry specific frequency bands for deploying private wireless networks.

The Mesh Rider Radio employs Doodle Labs' patented Mesh Rider® technology with state-of-the-art RF and networking capabilities that enable communication further, faster, and more reliably than any comparable solution on the market. For example, optimized video streaming carries crystal clear 4K video while simultaneously carrying Ultra Reliable Low Latency (URLLC) command and control (C&C) data for machines.

For more information, please visit:


Frequency Bands

Band Frequency Range
5700-MHz 5650-MHz to 5755 MHz
Japan Unmanned UAV (Licensed)

Key Features - Mesh Rider Radio Platform


  • Long range (field tested >100km) and high throughput (up to 100 Mbps) Mesh Rider waveform
  • Interference resistant COFDM for robust link quality in difficult RF environments
  • Exceptional Multipath and NrLOS MIMO performance
  • Adaptive radio modulations from BPSK up to 64QAM, with fast per packet optimization to maximize link performance in dynamic environments
  • Software defined channel bandwidth for efficient re-use of spectrum
  • Convolutional coding, Forward Error Correction (FEC), ACK-retransmits, Maximal Ratio Combining, Spatial Multiplexing, and Space Time Block Coding for robust data transmission over noisy channel/spectrum
  • Single channel, Time Division Duplexing (TDD) for bi-directional traffic
  • Resistant to high-power jamming signals
  • ATPC for widely dispersed mesh network
  • Built-in Spectrum Scanner to help mitigate interference issues


  • Ultra-Reliable Low Latency Channel (URLLC) for Command and Control
  • Optimized video streaming channel for Unicast and Multicast transport
  • Self-healing/self-forming multi-frequency mobile mesh for highly reliable network with redundancy
  • FIPS Certified AES 256- and 128-bit encryption
  • End-to-end IP architecture with Ad Hoc, WDS transparent bridge, Client, AP, and Internet Gateway operating modes
  • Embedded network management APIs


  • Very small size, weight, and power for mobile applications
  • Ethernet, USB, and UART interfaces to allow easy integration into different system architectures
  • Leverage the benefits of the most extensible OpenWrt ecosystem and install 3rd party IoT applications
  • Rugged, vibration resistant construction to meet MIL-specs
  • MIL-spec temp range (-40C to +85C)
  • High quality, manufactured in ISO 9001 and ISO 14001 certified facilities
  • COTS – Commercial off the Shelf
  • Extended lifespan and availability

System Integration


The Mesh Rider Radio has been designed to be plug and play. Only USB and a power supply are required for integration.

Visit Doodle Labs Technical Library for extensive design-in documents.



Technical Specifications (5700-MHz)

Model Category XTreme
Radio Configuration 2x2 MIMO
Model # Wearable:
RM-5700-12W3 (w/ Battery, GPS)
Antenna (Optional) ANT-5500-3-O
Evaluation Kit (Optional) EK-5700-22W: 2x Multi-band Antenna, Cables
Design-In Documentation Doodle Labs Technical Library
Data Throughput at 10-meter range with Attached 3 dBi Antennas (Indicative) 80 Mbps (20 MHz Channel)
40 Mbps (10 MHz Channel)
20 Mbps (5 MHz Channel)
Over the Air Data Encryption 128-bit AES (Full throughput)
256-bit AES (12 Mbps max throughput)
FIPS Certification (Optional) FIPS 140-3
Operating Modes WiFi Radio: AP, Client
Mesh, WDS AP, WDS Client
Bridged or Internet Gateway with NAT
Command & Control channel Ultra-Reliable Low Latency Channel (URLLC). Latency 1.5-10 ms
Video Channel Optimized video streaming with Unicast and Multicast transmission
Protocol Compatibility Fully compatible with Doodle Labs Mesh Rider Waveform
Operating Bands (Software Selectable) 5650-5755 MHz
Advanced Band Filters Dedicated filters for high interference immunity
Max RF Power at SMA port (Software control)
Each radio individually calibrated
1.0W (30 dBm) @ MCS 0,8
0.8W (29 dBm) @ MCS 3,11
0.5W (27 dBm) @ MCS 5,13
250mW (24 dBm) @MCS 7,15
Channel Sizes
(Software Selectable)
5, 10, 20 MHz
Radio Data Rate Auto adapting Modulation Coding Scheme (MCS0-15)
Antenna Signal Strength -30 to -90 dBm (Recommended), Absolute Maximum= +12 dBm
RF Power Control In 1 dBm steps, Tolerance ±1 dBm
Automatic Transmit Power Control (ATPC) Intelligently adjusts the transmit power for very close range operation
Integrated Antenna Port Protection Able to withstand open port, >10 KV (contact) and >15KV (open air discharge) as per IEC-61000-4-2
Wireless Error Correction FEC, ARQ
Receive Noise Figure +4 dB
Receive Adjacent Channel Rejection (ACRR) 34 dB @ MCS0 for 20 MHz channel (Typ)
Transmitter Adjacent Channel Leakage Ratio (ACLR) < 28 dBr (Fc ± ChBW)
Transmitter Spurious Emission Suppression < 40 dBc
Frequency Accuracy ±10 ppm max over life
WiFi Standard IEEE 802.11n, 1x1 SISO
Frequency Range 2400 - 2482 MHz and 5160 - 5825 MHz
RF Power Output (Typ) 50 mW (17 dBm) EIRP
Channel Size 20 MHz
Radio Data Rate Auto adapting Modulation Coding Scheme (MCS 0-7)
Antenna Signal Strength -25 to -85 dBm (Recommended), Absolute Maximum= +12 dBm
RF Power Control In 1 dBm steps, Tolerance ±1 dBm
Wireless Error Correction FEC, ARQ
Mesh Router Self-Forming/Self-Healing, Peer to Peer
Custom Software Package Manager Image Builder, OPKG, ipk
Radio Management Web GUI (HTTPs), SSH and JSON-RPC
Access control Password, MAC, IP, Port filtering
Supported Protocols IPv6, QoS, DNS, HTTPS, IP, ICMP, NTP, DHCP
Software Upgrade Over the air software upgrade supported
Power Input 6V - 24V, USB-PD Compliant
DC Power Consumption 5700 MHz:
14W Peak Tx power @ max range, 5W Rx mode, 2W Standby Mode
Dimensions 134.3mm x 63.0mm x 17.0mm
203 grams, 467 grams with battery
Mesh Rider Antenna Ports 2x TNC-Female Connector
Host Interface Wearable: USB-Device Interface (Ethernet only)

External: USB-Device Interface (Ethernet only), Ethernet (100 Base-T), 1x UART (3.3V), USB-Host
Temperature range (Operating) Industrial: -30°C to +70°C
* System's thermal design should ensure that the radio's case temperature is maintained within these specifications.
Temperature range (Non-Operating) -40°C to +100°C
Ingress Protection Waterproof (IP67)
Relative Humidity 5% to 95% noncondensing
Shock and Vibration Resistance Compliant to MIL-STD-810H for high shock and vibration
Reliability Extreme Reliability, IPC Class 2 standard with Class 3 options
WiFi Hotspot Antennas 1x Embedded Antenna
GPS Features Simultaneous multiple constellations (GPS/SBAS/Galileo/Glonass/BeiDou/QZSS)

Receive Sensitivity -167 dBm, Max. Velocity 500m/sec ± 0.05m/S, Heading ± 0.3 degrees, Position Accuracy 2m
Integrated GPS Module with LNA u-blox NEO-M9N module Concurrent GNSS Module (
GPS Antenna 1x Embedded Antenna
Integrated CPU MIPS 24Kc, 540 MHz, 32MB Flash, 64MB DDR2 RAM
ESD Protection IEC 61000-4-2 test criteria, Level 3 (±6KV) for Contact Discharge and Level 4 (±15KV) for Air Discharge
MTBF >235k hours (25 years)
Life Cycle Planning Extended lifespan with 7 years guaranteed availability
J/F-12 Certification N.A.
Industry Canada (IC) N.A.
Japan (MIC) Certified under Article 2-1-72
Unmanned Mobile Image Transmission System
(In Progress)
Regulatory Requirements Designed and verified to meet various regulatory requirements. Formal testing and approval are required for the Integrator's antenna type. The Integrator is responsible for obtaining all regulatory approvals in target markets for the finished product.
RoHS/WEEE Compliance Yes. 100% Recyclable/Biodegradable packaging
ECCN Code 5A992
HS Code 85256010


MCS Rate Modulation Combined Output Power (dBm) Sensitivity (dBm) UDP Throughput (Mbps)
0 BPSK (1/2) 30 -93 5.4
1 QPSK (1/2) 29 -91 10.62
2 QPSK (3/4) 29 -89 15.66
3 16-QAM (1/2) 29 -87 20.52
4 16-QAM (3/4) 28 -83 29.88
5 64-QAM (2/3) 27 -79 38.88
6 64-QAM (3/4) 26 -77 43.11
7 64-QAM (5/6) 24 -75 47.34
8 BPSK (1/2) 30 -90 10.53
9 QPSK (1/2) 29 -88 20.43
10 QPSK (3/4) 29 -86 29.7
11 16-QAM (1/2) 29 -84 38.52
12 16-QAM (3/4) 28 -80 54.72
13 64-QAM (2/3) 27 -76 69.3
14 64-QAM (3/4) 26 -74 76.14
15 64-QAM (5/6) 24 -72 82.8

Note 1: Performance based on 20-MHz bandwidth
Note 2: Sensitivity and throughput are approximately proportional to bandwidth.