Simple Configuration Profiles
      Back to home
      1. Doodle Labs Technical Library
      2. Software Guides
      3. Simple Configuration Profiles

      Simple Configuration Profiles

      This document provides a list of simple configuration profiles and the corresponding settings they adjust. The profiles aim to streamline the setup process by offering predefined configurations tailored for specific use cases.

      Profiles 

       

      General  
      1. Default profile with most frequently used configuration settings  
      2. Transmit Power Control ON (In all modes) 
      3. Aggressive Transmit Power Control ON (In all modes) 
      4. Wide Bandwidth 
      5. Number of nodes (default: 1 to 2) 
      6. Turn off low latency optimizations 
      UAV/UGV/Robot 
      1. Mesh/WDS Client Only 
      2. GCS Finder or serial port client 
      3. Sense client  
      4. 10-MHz bandwidth 
      5. Transmit Power Control ON (dynamic_txpower) (In all modes) 
      6. Aggressive Transmit Power Control ON (both dynamic_txpower and dynamic_txpower_aggr should be on) (In all modes) 
      7. Turn off low latency optimizations 
      8. Number of nodes (default: 1 to 2) 
      GCS 
      1. Mesh/WDS AP Only 
      2. Sense Master 
      3. 10-MHz bandwidth 
      4. Transmit Power Control ON  (dynamic_txpower) (In all modes) 
      5. Aggressive Transmit Power Control ON (both dynamic_txpower and dynamic_txpower_aggr should be on) (In all modes) 
      6. Turn off low latency optimizations 
      7. Number of nodes (default: 1 to 2) 
      GCS with Internet 
      1. Mesh/WDS AP Only 
      2. Gateway for internet access when Wi-Fi is EUD 
      3. EUD Wizard ON 
      4. Optional serial port server 
      5. Sense Master 
      6. 10-MHz bandwidth 
      7. Transmit Power Control ON (In all modes) 
      8. Aggressive Transmit Power Control ON (In all modes) 
      9. RTK GPS setup 
      10. Choose Wi-Fi or USB. In Wi-Fi mode, enable port forwarding. Detect drone IP address (only 1 DHCP address to serve?) 
      11. Turn off low latency optimizations 
      12. Number of nodes (default: 1 to 2) 
      Factory infrastructure 
      1. WDS AP Only 
      2. Wide Bandwidth 
      3. Transmit Power Control ON (In all modes) 
      4. Aggressive Transmit Power Control OFF (In all modes) 
      5. Turn off low latency optimizations 
      6. Number of nodes (default: 10+) 
      Factory robot 
      1. WDS Client Only 
      2. Wide Bandwidth 
      3. Transmit Power Control ON (In all modes) 
      4. Aggressive Transmit Power Control OFF (In all modes) 
      5. Turn off low latency optimizations 
      6. Number of nodes (default: 10+) 
      Factory Mesh 
      1. Mesh Only 
      2. Wide Bandwidth 
      3. Bridge Loop Avoidance 
      4. Number of nodes (default: 10+) 
      5. Transmit Power Control ON (In all modes) 
      6. Aggressive Transmit Power Control OFF (In all modes) 
      7. Turn off low latency optimizations 
      Connected Teams 
      1. Mesh Only 
      2. Wide Bandwidth 
      3. Number of nodes (default: 10+) 
      4. Transmit Power Control ON (In all modes) 
      5. Aggressive Transmit Power Control OFF (In all modes) 
      6. Turn off low latency optimizations 
      Max Throughput 
      1. Number of nodes (default: 10+) 
      2. Transmit Power Control OFF (In all modes) 
      3. Aggressive Transmit Power Control OFF (In all modes) 
      4. disable diffserv service 
      5. Turn off low-latency settings. 
      6. maximum channel bandwidth (26-MHz or 40-MHz) 
      7. Mesh (default) / WDS AP / Client 
      8. Wide Bandwidth